.WebSite
|
ABOUT ADLSAsymmetric digital subscriber line (ADSL) is a form of DSL, a data communications technology that enables faster data transmission over copper telephone lines than a conventional voiceband modem can provide. It does this by utilizing frequencies that are not used by a voice telephone call. A splitter - or microfilter - allows a single telephone connection to be used for both ADSL service and voice calls at the same time. ADSL can generally only be distributed over short distances from the central office, typically less than 4 kilometres (2 mi), but has been known to exceed 8 kilometres (5 mi) if the originally laid wire gauge allows for farther distribution. At the telephone exchange the line generally terminates at a DSLAM where another frequency splitter separates the voice band signal for the conventional phone network. Data carried by the ADSL is typically routed over the telephone company's data network and eventually reaches a conventional internet network.
EXPLANATIONThe distinguishing characteristic of ADSL over other forms of DSL is that the volume of data flow is greater in one direction than the other, i.e. it is asymmetric. Providers usually market ADSL as a service for consumers to connect to the Internet in a relatively passive mode: able to use the higher speed direction for the "download" from the Internet but not needing to run servers that would require high speed in the other direction.There are both technical and marketing reasons why ADSL is in many places the most common type offered to home users. On the technical side, there is likely to be more crosstalk from other circuits at the DSLAM end (where the wires from many local loops are close to each other) than at the customer premises. Thus the upload signal is weakest at the noisiest part of the local loop, while the download signal is strongest at the noisiest part of the local loop. It therefore makes technical sense to have the DSLAM transmit at a higher bit rate than does the modem on the customer end. Since the typical home user in fact does prefer a higher download speed, the telephone companies chose to make a virtue out of necessity, hence ADSL. On the marketing side, limiting upload speeds limits the attractiveness of this service to business customers, often causing them to purchase higher cost Leased line services instead. In this fashion, it segments the digital communications market between business and home users.
HOW ADSL WORKSOn the wireCurrently, most ADSL communication is full-duplex. Full-duplex ADSL communication is usually achieved on a wire pair by either frequency-division duplex (FDD), echo-cancelling duplex (ECD), or time-division duplexing (TDD). FDD uses two separate frequency bands, referred to as the upstream and downstream bands. The upstream band is used for communication from the end user to the telephone central office. The downstream band is used for communicating from the central office to the end user. With standard ADSL (annex A), the band from 25.875 kHz to 138 kHz is used for upstream communication, while 138 kHz – 1104 kHz is used for downstream communication. Each of these is further divided into smaller frequency channels of 4.3125 kHz. These frequency channels are sometimes termed bins. During initial training, the ADSL modem tests each of the bins to establish the signal-to-noise ratio at each bin's frequency. The distance from the telephone exchange and the characteristics of the cable mean that some frequencies may not propagate well, and noise on the copper wire, interference from AM radio stations and local interference and electrical noise at the customer end mean that relatively high levels of noise are present at some frequencies, so considering both effects the signal-to-noise ratio in some bins (at some frequencies) may be good or completely inadequate. A bad signal-to-noise ratio measured at certain frequencies will mean that those bins will not be used, resulting in a reduced maximum link capacity but with an otherwise functional ADSL connection. The DSL modem will make a plan on how to exploit each of the bins sometimes termed "bits per bin" allocation. Those bins that have a good signal-to-noise ratio (SNR) will be chosen to transmit signals chosen from a greater number of possible encoded values (this range of possibilities equating to more bits of data sent) in each main clock cycle. The number of possibilities must not be so large that the receiver might mishear which one was intended in the presence of noise. Noisy bins may only be required to carry as few as two bits, a choice from only one of four possible patterns, or only one bit per bin in the case of ADSL2+, and really noisy bins are not used at all. If the pattern of noise versus frequencies heard in the bins changes, the DSL modem can alter the bits-per-bin allocations, in a process called "bitswap", where bins that have become more noisy are only required to carry fewer bits and other channels will be chosen to be given a higher burden. The data transfer capacity the DSL modem therefore reports is determined by the total of the bits-per-bin allocations of all the bins combined. Higher signal-to-noise ratios and more bins being in use gives a higher total link capacity, while lower signal-to-noise ratios or fewer bins being used gives a low link capacity. The total maximum capacity derived from summing the bits-per-bins is reported by DSL modems and is sometimes termed sync rate. This will always be rather misleading as the true maximum link capacity for user data transfer rate will be significantly lower because extra data is transmitted that is termed protocol overhead, a reduced figure of around 84-87% at most for PPPoA connections being a common example. In addition some ISPs will have traffic policies that limit maximum transfer rates further in the networks beyond the exchange, and traffic congestion on the Internet, heavy loading on servers and slowness or inefficiency in customers' computers may all contribute to reductions below the maximum attainable. The choices the DSL modem make can also be either conservative, where the modem chooses to allocate fewer bits per bin than it possibly could, a choice which makes for a slower connection, or less conservative in which more bits per bin are chosen in which case there is a greater risk case of error should future signal-to-noise ratios deteriorate to the point where the bits-per-bin allocations chosen are too high to cope with the greater noise present. This conservatism involving a choice to using fewer bits per bin as a safeguard against future noise increases is reported as the signal-to-noise ratio margin or SNR margin. The telephone exchange can indicate a suggested SNR margin to the customer's DSL modem when it initially connects, and the modem may make its bits-per-bin allocation plan accordingly. A high SNR margin will mean a reduced maximum throughput but greater reliability and stability of the connection. A low SNR margin will mean high speeds provided the noise level does not increase too much, otherwise the connection will have to be dropped and renegotiated (resynced). ADSL2+ can better accommodate such circumstances, offering a feature termed seamless rate adaptation (SRA), which can accommodate changes in total link capacity with less disruption to communications. Vendors may support usage of higher frequencies as a proprietary extension to the standard. However, this requires matching vendor-supplied equipment on both ends of the line, and will likely result in crosstalk problems that affect other lines in the same bundle. There is a direct relationship between the number of channels available and the throughput capacity of the ADSL connection. The exact data capacity per channel depends on the modulation method used.
ModulationADSL initially existed in two flavours (similar to VDSL), namely CAP and DMT. CAP was the de facto standard for ADSL deployments up until 1996, deployed in 90 percent of ADSL installs at the time. However, DMT was chosen for the first ITU-T ADSL standards, G.992.1 and G.992.2 (also called G.dmt and G.lite respectively). Therefore all modern installations of ADSL are based on the DMT modulation scheme. Annexes J and M shift the upstream/downstream frequency split up to 276 kHz (from 138 kHz used in the commonly deployed annex A) in order to boost upstream rates. Additionally, the "all-digital-loop" variants of ADSL2 and ADSL2+ (annexes I and J) support an extra 256 kbit/s of upstream if the bandwidth normally used for POTS voice calls is allocated for ADSL usage. ADSL1 access utilizes the 1.1 MHz band, and ADSL2+ utilizes the 2.2 MHz band. The downstream and upstream rates displayed are theoretical maxima. Note also that because digital subscriber line access multiplexers and ADSL modems may have been implemented based on differing or incomplete standards some manufacturers may advertise different speeds. For example, Ericsson has several devices that support non-standard upstream speeds of up to 2 Mbit/s in ADSL2 and ADSL2+.
INSTALLATION ISSUESDue to the way it uses the frequency spectrum, ADSL deployment presents some issues. It is necessary to install appropriate frequency filters at the customer's premises, to avoid interference with the voice service, while at the same time taking care to keep a clean signal level for the ADSL connection. In the early days of DSL, installation required a technician to visit the premises. A splitter or microfilter was installed near the demarcation point, from which a dedicated data line was installed. This way, the DSL signal is separated earlier and is not attenuated inside the customer premises. However, this procedure is costly, and also caused problems with customers complaining about having to wait for the technician to perform the installation. As a result, many DSL vendors started offering a self-install option, in which they ship equipment and instructions to the customer. Instead of separating the DSL signal at the demarcation point, the opposite is done: the DSL signal is filtered at each phone outlet by use of a low-pass filter for voice and a high-pass filter for data, usually enclosed in what is known as a microfilter. This microfilter can be plugged directly into any phone jack, and does not require any rewiring at the customer's premises. A side effect of the move to the self-install model is that the DSL signal can be degraded, especially if more than 5 voiceband devices are connected to the line. The DSL signal is now present on all telephone wiring in the building, causing attenuation and echo. A way to circumvent this is to go back to the original model, and install one filter upstream from all telephone jacks in the building, except for the jack to which the DSL modem will be connected. Since this requires wiring changes by the customer and may not work on some household telephone wiring, it is rarely done. It is usually much easier to install filters at each telephone jack that is in use. DSL signals may be degraded by older telephone lines, surge protectors, poorly designed microfilters, radio frequency interference, electrical noise, and by long telephone extension cords. Telephone extension cords are typically made with small-gauge multi-strand copper conductors which do not maintain a noise-reducing pair twist. Such cable is more susceptible to electromagnetic interference and has more attenuation than solid twisted-pair copper wires typically wired to telephone jacks. These effects are especially significant where the customer's phone line is more than 4 km from the DSLAM in the telephone exchange, which causes the signal levels to be lower relative to any local noise and attenuation. This will have the effect of reducing speeds or causing connection failures.
ADSL LOOP EXTENDERAn ADSL loop extender or ADSL repeater is a device that a telephone company can place midway between the subscriber and central office to extend the distance and increase the channel capacity of their DSL connection. ADSL repeaters are aggressively deployed by rural telephone companies trying to provide rural Internet service to farms and small towns where it's impractical to place the DSLAM closer. The typical distance improvement with a loop extender is shown in the diagram below, with rate in Megabits per second and distance in thousands of feet.
HOLIDAYS
A repeater can either be an amplifier or a regenerator. Amplifiers increase the signal level of the analog transmission signal; regenerators demodulate the signal to binary, then re-modulate it into the original transmission frequency. Because regeneration restores the signal to binary, an indefinite number of regenerators can be placed on a line and is the preferred choice for services like T1 (Digital Signal 1) that have no distance limits. Because of the simplicity of the amplifier circuits, amplifiers are of lower cost than regenerators. It's the cost of regenerators that drives the price differences between T1 at $800 per month and ADSL at $40 per month. Because ADSL is a low-cost service, it's generally felt that the additional cost of regeneration cannot be supported. ADSL repeaters all work through amplification instead of regeneration. Before the development of ADSL loop extenders, ADSL had been limited to 3-6 miles from the Central Office depending on the wire gauge used. An ADSL Loop Extender works as an amplifier, boosting the signal level so it can travel longer distances. In some cases, service can now be established as far as 10 miles from the Central Office. In 2006, US telco promoted Fiber to the Home. This was driven by a rapidly growing housing sector that was creating the “greenfield” customers that are needed to make fiber to the home profitable. Later, with the housing sector in a serious recession, that "greenfield" seems to be drying up fast. With most of the “brownfield” market already tapped for ADSL, Telcos finally are interested in extending ADSL to those semi-rural areas that have never been important before. Some ADSL loop extenders aren't repeaters, but instead convert to a different signal (like G.shdsl) that can be repeater-ed. If additional amplification in the C.O. were a good idea, the DSLAM and modem makers would just run their products at higher power. This additional amplification creates noise on adjacent pairs and is not compliant with T1.417 spectrum management. Converting to G.shdsl or other technologies has problems too. These technologies have limited downstream speed, thus are less useful except to extend services to the most distant customers. Because the technology has so many components (special C.O., regenerators, CPE), it's much more expensive than ADSL amplifiers.
CHEAP WEB HOSTING
HostGator is a leading provider of web hosting, reseller hosting, and dedicated servers. Over 2.5 million websites trust HostGator for their web hosting
Make money taking pictures with your digitalHow to sell your photos online or How to sell your illustrations onlineAll you do need is a digital camera and access to the Internet. ... What to take pictures of – find out what types of images are in the most demand here! About earning money via internet. I want to make it very clear upfront that it is not about getting rich quickly; neither it is about "earn $300 a day working from home" neither it is about online casinos, online marketing or any other such thing. This article is to provide the guidance for photographers (and other digital artists) about possibilities to get income from their photographs (or other digital works) using internet. More specifically.
ONLINE STOCK PHOTO AGENCIESStock photo agencies are sometimes referred to as photo archives, picture libraries, or image banks.The sites listed below are known as 'micro stock' sites, they allow anyone from the amateur to the professional photographer to sell images easily. These sites take images from individual contributors, and photographer gets a commission for each image sold. Micro stock agencies sell royalty-free images starting at as low as $1, and while the fees on each image are low - typically less than a dollar on each sale - the companies sell large volumes of images. The mindset of micro stock is that quantity will prevail and the photographers will end up making as much from many small sales as they would from a few large sales on a traditional stock photography site. Quality and quantity of your images will determine how much you will earn.
.................................................................................................................................
|
